«

»

Backwoods Blacksmithing How To Make A Forge

How To Make A Forge For Backwoods Blacksmithing

Guest article, kindly sent in by: 
Gary Johnston – Jack Raven Bushcraft & Ross Berry – Kaos Blacksmiths

If you’ve ever wanted to be able to make some of your own bushcraft kit, such as knives and traditional fire steels, but thought that building a forge was out of your budget or skill set, then here is an easy way to build one either in the woods or in your garden.

In this article I’ll show you how to make your own woodland pit forge using only some flexible hose, clay and an old 12v bilge pump all for about £30 and some ingenuity.

Dig a rectangular hole about 50cm long and 30cm wide by around 15cm deep.
You want to check the soil to make sure that there aren’t any stones that might explode. If you do have soil that is, for instance, flinty, dig the hole bigger and line it with sand.

To make the whole forging process easier you’ll need to make a ‘tue iron’.

A ‘tue iron’ is a device to accelerate the flow of air into the forge; the term itself is from Kent and is a corruption of the French ‘tuyere’.

Here you can see I’ve used about a meter of 40mm of flexible hose and laid it into the hole, about a third of the way in, although you could just as easily use some steel pipe.

Next was to dig some clay out of the back garden and take it with me to the woods (it’s mostly chalk where our camp is on the Kent Downs), although you can buy it from the garden centre.

Again, make sure there are no stones in it. I used the clay to construct the back plate as shown in the photo.

At this point you need to wet the flexible hose and push it forward about 10cm.

Make sure that you mould the clay all around the flexible hose until it is about 100mm depth all the way around.

You’ll need to keep wetting the clay to mould it around.

Build up the back plate until it’s another 10 or 15cm high.

Now pull the flexible hose back 10cm so that it is in its original position.

This is so that it doesn’t melt when the forge is in use.

You could use bellows, but it isn’t easy on your own, and even if you have someone helping out it gets quite  tiring.

So instead, I‘ve used a 12v bilge extractor from a boat that cost £15 online.

In my case I needed to add a rheostat to adjust the airflow.
You can find them in amps, or even toasters, but failing that you can buy them for a few pounds.

If you prefer buying new,  there are still lots of small pumps to choose from.

A typical bilge pump like this compact Idealeben 12V 30mm Stainless Steel Submersible Pump will pump water or air at a rate of 12 Lts/min 

This pump will cost you under £12 from Amazon.​

To control this flow rate the external speed control is fitted.

A simple speed controller  (rheostat)  for the above pump is dead easy to wire up with only four connections:
two in and two out.

This is the MagiDeal Motor Speed Controller, costing under £3.

The cone is made from some scrap aluminium and simply joins the blower to the flexible hose.
The whole thing can be connected to a 12v battery, which in turn can be charged from a solar panel, although a decent solar panel alone should power the forge.

I use charcoal in the forge. After I’d built the pit forge I lit a small quantity of charcoal so that the clay didn’t dry too quickly and crack.

The forge has been in the woods at our ancient woodland camp in Kent for 2 years now and regularly used on our ‘Blacksmithing, Bodging & Bushcraft’ courses, as demonstrated here by Vicky as she made a knife recently.

Since making the forge we’ve repaired a small crack, but otherwise it has been remarkably resilient and very effective.

Steve Hart UK Prepper

Great article, and a big thank you to Gary of Jack Raven Bushcraft., and to Ross of Kaos Blacksmiths for sending it in to me.

Such a simple idea, yet endless possibilities for survival out in the wild.​

Gary and Ross both run courses on all aspects of bushcraft and blacksmithing over in Kent.​ So if you are interested, just visit their website for more information.

Happy Prepping Folks.

* Enter your name & a valid Email address

* You will receive an Email titled 'Preppers Newsletter Subscription'.
*Simply confirm, and you've joined our community of preppers.

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong>